<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    metallurgical cylinder Sold to El Salvador

    Release time:2023-11-12 15:27:42 Hits: Current position: Home > News

    This article mainly introduces:

    El Salvador hydraulic cylinder,metallurgical cylinder manufacturer,metallurgical cylinder

    El Salvador metallurgical cylinder

    (El Salvador metallurgical cylinder,produced by Hebei Hengyu company)

    metallurgical cylinder are widely used in El Salvador,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed metallurgical cylinder for customers from El Salvador.

    Introduction to metallurgical cylinder:

    metallurgical cylinder buffer valve inspection and maintenance: For the valve buffer metallurgical cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

    The piston seal of the metallurgical cylinder is the main element to prevent leakage in the metallurgical cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

    When the metallurgical cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

    The material of the sliding part of the metallurgical cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

    Answers to some questions about metallurgical cylinder:

    How to control the speed of the cylinder?
    High demand control, it is necessary to use servo closed-loop control, you can adjust the speed at will. Reference: Hydrodynamic Motion Control Practical Design Guide.

    When the hydraulic cylinder changes from fast to slow, how can the slow speed become more even and the speed can be adjusted?
    Reversing valve set 2 reversing valves. The back of one valve goes directly to the cylinder, running at full speed for fast action. Add a speed control valve behind the other valve, and then connect to the cylinder to achieve slow action, you can adjust the opening of the speed control valve, to achieve the speed of the cylinder can be adjusted. An import speed control valve to more than 1,000 yuan, if you think it is too expensive, you can also use the throttle valve instead. However, the throttle valve is greatly affected by the load change.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 白山市| 江口县| 黎平县| 荔波县| 青龙| 东港市| 黄山市| 普陀区| 广安市| 商南县| 漳浦县| 沙坪坝区| 犍为县| 白朗县| 界首市| 长泰县| 中牟县| 兴义市| 桑植县| 淮安市| 靖宇县| 岳西县| 抚顺县| 东乡| 西平县| 塘沽区| 那曲县| 石家庄市| 莲花县| 梁平县| 长治市| 赞皇县| 临泉县| 宣恩县| 华阴市| 沙河市| 夏河县| 揭阳市| 土默特右旗| 崇州市| 蛟河市|