<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    steering cylinder Sold to Slovakia

    Release time:2023-11-12 15:28:29 Hits: Current position: Home > News

    This article mainly introduces:

    Slovakia hydraulic cylinder,steering cylinder manufacturer,steering cylinder

    Slovakia steering cylinder

    (Slovakia steering cylinder,produced by Hengyu Group)

    steering cylinder are widely used in Slovakia,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed steering cylinder for customers from Slovakia.

    Introduction to steering cylinder:

    steering cylinder use should try to avoid sealing belt into the steering cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the steering cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the steering cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

    The assembly work of the steering cylinder has a great impact on the quality of the steering cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

    steering cylinder can not drive the load troubleshooting: oil pressure is too low. steering cylinder selection specifications are too small. Leakage in steering cylinder or associated hydraulic system element.

    The material of the sliding part of the steering cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

    Answers to some questions about steering cylinder:

    How to deal with the surface degreasing process before spraying paint after cylinder assembly, and what degreasing agent is used?
    Cylinder painting, generally using the following process (note: the cylinder is best painted, do not spray powder coating, because the powder coating curing temperature is high, will lead to sealing defects and oil leakage) : Pre-degreasing - degreasing - washing - washing - pickling - washing - washing - table adjustment - phosphating - washing - washing - drying - polishing - spray primer - spray paint degreasing agent generally use neutral or weak alkaline degreasing agent, phosphating liquid generally use zinc phosphating liquid.

    What is the meaning of dead volume in hydraulic cylinder?
    Closed volume, also known as dead zone volume Positive displacement pump is dependent on the change of sealing working volume to achieve suction and pressure oil, in order not to make the suction and pressure oil cavity interworking, there is an oil sealing area between the suction and pressure oil cavity, when the sealing working volume passes through the oil sealing area, neither pressure oil cavity nor oil suction cavity communication, forming a closed sealing volume. The unloading groove is opened, and the grooving principle is that the sealing volume decreases and the oil pressure chamber is communicated, and the sealing volume increases and the oil suction chamber is communicated.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 渭南市| 沧州市| 永济市| 射洪县| 黔江区| 石泉县| 壤塘县| 报价| 宜宾市| 黎平县| 公主岭市| 工布江达县| 渭源县| 深泽县| 开封县| 五莲县| 厦门市| 周口市| 山阳县| 新建县| 嘉义县| 化隆| 长治市| 余姚市| 宁津县| 阿克陶县| 娱乐| 巴林右旗| 新源县| 清新县| 大洼县| 凤城市| 稻城县| 香港| 长治市| 合山市| 名山县| 改则县| 重庆市| 克山县| 图们市|