<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    reset cylinder Sold to Switzerland

    Release time:2023-11-12 15:31:27 Hits: Current position: Home > News

    This article mainly introduces:

    Switzerland hydraulic cylinder,reset cylinder manufacturer,reset cylinder

    Switzerland reset cylinder

    (Switzerland reset cylinder,produced by Hengyu Hydraulic Cylinder Factory)

    reset cylinder are widely used in Switzerland,because of high work efficiency,excellent fatigue and impact resistance,smooth movement.So our company has designed reset cylinder for customers from Switzerland.

    Introduction to reset cylinder:

    In use, the reset cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the reset cylinder.

    When the reset cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the reset cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the reset cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the reset cylinder can meet the requirements by grinding. However, the life and reliability of this repair reset cylinder are not high.

    How to determine the working pressure of the reset cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, reset cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

    The internal leakage of the reset cylinder is an important indicator to measure the quality of the reset cylinder: the internal leakage of the reset cylinder will reduce the volumetric efficiency, increase the temperature rise of the oil, affect the positioning accuracy of the reset cylinder, so that the reset cylinder can not accurately and stably stop in a certain position of the reset cylinder, so it is one of the main indicators of the reset cylinder.

    Answers to some questions about reset cylinder:

    Injection molding machine die thimble on the side of the feed nozzle, the oil cylinder pull the thimble shift, how to debug the oil cylinder?
    The cylinder is connected with the neutron of the injection molding machine, the neutron is retreated after the opening mold is in place, the cylinder taps the thimble plate to the top, and then takes, and the neutron is reset.

    What is the material of the lift cylinder?
    The cylinder is composed of many parts. The cylinder also contains the seal and the installation port at both ends, the material of these two parts is not easy to determine if there is no physical object. The cylinder body is generally 20 steel, 45 steel, 27SiMn and other materials, and the piston rod is generally 40Cr, 45 steel and other materials.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 长宁县| 宝应县| 西平县| 无棣县| 藁城市| 峡江县| 博爱县| 沙湾县| 宿松县| 阳江市| 龙游县| 台东市| 永丰县| 沁源县| 浦县| 中江县| 辽宁省| 诸暨市| 全州县| 丽江市| 格尔木市| 镇安县| 达拉特旗| 富裕县| 南通市| 大关县| 类乌齐县| 安阳市| 合水县| 宁陕县| 阳谷县| 文水县| 永平县| 信阳市| 麦盖提县| 孟州市| 固安县| 清镇市| 迁西县| 茂名市| 凤山县|