<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    tailplate hydraulic cylinder Sold to Guatemala

    Release time:2023-11-12 15:31:54 Hits: Current position: Home > News

    This article mainly introduces:

    Guatemala hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

    Guatemala tailplate hydraulic cylinder

    (Guatemala tailplate hydraulic cylinder,produced by Hengyu Group)

    tailplate hydraulic cylinder are widely used in Guatemala,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed tailplate hydraulic cylinder for customers from Guatemala.

    Introduction to tailplate hydraulic cylinder:

    When the initial action of the tailplate hydraulic cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the tailplate hydraulic cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

    When the tailplate hydraulic cylinder needs to be stored for a period of time, please follow the recommended methods: The tailplate hydraulic cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the tailplate hydraulic cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil tailplate hydraulic cylinder should not be in direct contact with water vapor for a long time. The tailplate hydraulic cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the tailplate hydraulic cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the tailplate hydraulic cylinder Before working, the tailplate hydraulic cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the tailplate hydraulic cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

    When the hydraulic oil is not pumped into the tailplate hydraulic cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the tailplate hydraulic cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

    In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular tailplate hydraulic cylinder action. Troubleshooting method: Replace the rubber hose.

    Answers to some questions about tailplate hydraulic cylinder:

    Are hydraulic cylinders divided into oil cylinders and water cylinders? What's the difference between the two types?
    There are oil cylinders and water cylinders. The two cylinders are used in different environments. Oil cylinders are generally used in places where there is less demand for media, which is our most common hydraulic cylinders. Water cylinders are mainly used for large tonnage presses. Because the equipment is too large, the use of hydraulic oil will cause a relatively large waste. However, water is not pure water, there are oil-in-water emulsion and water-in-oil emulsion. Water has another benefit: it's flame retardant. It is especially suitable for some flammable and explosive occasions. Or with water glycol. The use of pure water is very little, mainly because the seal is not good and easy to rust.

    How to design the guide sleeve of cylinder diameter 400?
    The purpose of the guide sleeve is to guide and seal. Therefore, it is necessary to look at the speed of the piston rod, working pressure and radial force. High speed, medium pressure, no (or very little) radial force, with a Steseal. Low speed and heavy load, medium radial force, combined seal. High speed and heavy load, large radial force, sealed with DU sleeve + copper ring + combination. The combination seal must have a lubricating oil passage, and a seal must be added to the outside of the oil passage.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 珠海市| 宣武区| 麻城市| 平果县| 安西县| 桃江县| 丁青县| 辽阳市| 珲春市| 乡宁县| 宜川县| 灵台县| 林芝县| 安阳市| 拉孜县| 调兵山市| 永寿县| 英山县| 武义县| 五河县| 万盛区| 温泉县| 菏泽市| 大足县| 泗洪县| 乐安县| 都匀市| 竹溪县| 大石桥市| 桓仁| 清丰县| 抚松县| 屏南县| 北宁市| 清新县| 怀安县| 安龙县| 南涧| 汨罗市| 萨迦县| 三亚市|