<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    punch machine hydraulic cylinder Sold to Ireland

    Release time:2023-11-12 15:33:11 Hits: Current position: Home > News

    This article mainly introduces:

    Ireland hydraulic cylinder,punch machine hydraulic cylinder manufacturer,punch machine hydraulic cylinder

    Ireland punch machine hydraulic cylinder

    (Ireland punch machine hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

    punch machine hydraulic cylinder are widely used in Ireland,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed punch machine hydraulic cylinder for customers from Ireland.

    Introduction to punch machine hydraulic cylinder:

    When the punch machine hydraulic cylinder is in use, ensure that the punch machine hydraulic cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

    Disassembly punch machine hydraulic cylinder: When disassembly punch machine hydraulic cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the punch machine hydraulic cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the punch machine hydraulic cylinder.

    The repair method of punch machine hydraulic cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

    In order to ensure the service life of the punch machine hydraulic cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

    Answers to some questions about punch machine hydraulic cylinder:

    Why is the hydraulic cylinder of the larger excavator arm upside down?
    The weight of the excavating arm of a large excavator will be very heavy, and an oil cylinder has two cavities, one is a rod cavity, and the other is a rodless cavity. The lifting force of the excavator is the product of the ortho-projection area of the piston rod cavity by the oil pressure, so the strength of the rodless cavity is much greater than that of the rod cavity. And the parallel bars with the piston rod facing down are also conducive to assembly and future maintenance. So a large excavator has to keep the cylinder facing down.

    Why the injection cylinder retreating after the injection molding machine is started?
    It is likely that the projected area of the molded plastic parts is large or the injection pressure set is relatively large, resulting in the expansion force exceeding the clamping force of the injection molding machine, so the mold is backward. You can do the following attempts: 1, reduce the injection force of the injection molding machine; 2, if the injection molding part can not be well formed by reducing the injection force, it is recommended to install the mold to a larger injection molding machine.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 会泽县| 安图县| 安福县| 钟祥市| 镇江市| 邵阳县| 家居| 建平县| 望都县| 涿鹿县| 岳阳市| 九江县| 安阳市| 南平市| 二手房| 天峨县| 大庆市| 杭锦旗| 涟源市| 新宾| 东乌珠穆沁旗| 石首市| 平顶山市| 连山| 本溪市| 易门县| 南召县| 科技| 蓝田县| 文成县| 莱阳市| 宜君县| 克拉玛依市| 雅江县| 信阳市| 临武县| 闵行区| 诸城市| 莱州市| 海淀区| 东安县|