<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    track steering cylinder Sold to Germany

    Release time:2023-11-08 08:11:37 Hits: Current position: Home > News

    This article mainly introduces:

    Germany hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

    Germany track steering cylinder

    (Germany track steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

    track steering cylinder are widely used in Germany,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed track steering cylinder for customers from Germany.

    Introduction to track steering cylinder:

    When the hydraulic oil is not pumped into the track steering cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the track steering cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

    The repair method of track steering cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

    When producing oil track steering cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

    When the track steering cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the track steering cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

    Answers to some questions about track steering cylinder:

    What is the meaning of dead volume in hydraulic cylinder?
    Closed volume, also known as dead zone volume Positive displacement pump is dependent on the change of sealing working volume to achieve suction and pressure oil, in order not to make the suction and pressure oil cavity interworking, there is an oil sealing area between the suction and pressure oil cavity, when the sealing working volume passes through the oil sealing area, neither pressure oil cavity nor oil suction cavity communication, forming a closed sealing volume. The unloading groove is opened, and the grooving principle is that the sealing volume decreases and the oil pressure chamber is communicated, and the sealing volume increases and the oil suction chamber is communicated.

    How to calculate hydraulic cylinder thrust?
    Cylinder diameter = piston diameter =200MM Piston area =π (200/2) square =3140 square mm =31.4 square cm 25MPA=250KG/ square cm Maximum thrust = pressure * Piston area =250 *31.4 =7850KG=78500 Newtons This is the maximum thrust. The formula can be derived from the calculation formula.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 镇坪县| 新龙县| 体育| 错那县| 德钦县| 永年县| 刚察县| 雅江县| 咸阳市| 邹平县| 德安县| 乌海市| 峨眉山市| 远安县| 靖江市| 怀集县| 海南省| 鄯善县| 芮城县| 宁海县| 郎溪县| 微山县| 井冈山市| 额济纳旗| 麦盖提县| 凤翔县| 大丰市| 铜梁县| 三亚市| 颍上县| 昌平区| 彭泽县| 剑阁县| 灵川县| 康定县| 永顺县| 天峨县| 阳新县| 通州市| 巩留县| 桑植县|