<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    stroke adjustable cylinder Sold to Czech Republic

    Release time:2023-11-15 10:42:01 Hits: Current position: Home > News

    This article mainly introduces:

    Czech Republic hydraulic cylinder,stroke adjustable cylinder manufacturer,stroke adjustable cylinder

    Czech Republic stroke adjustable cylinder

    (Czech Republic stroke adjustable cylinder,produced by Hengyu Hydraulic Cylinder Factory)

    stroke adjustable cylinder are widely used in Czech Republic,because of powerful torque,long service life,smooth movement.So our company has designed stroke adjustable cylinder for customers from Czech Republic.

    Introduction to stroke adjustable cylinder:

    The advantages and disadvantages of the stroke adjustable cylinder: the surface of the stroke adjustable cylinder by painting, coating protection treatment, bright luster is not easy to rust, all raw materials of the stroke adjustable cylinder through the top heat treatment, high manufacturing precision, belongs to the precision machinery, has a simple structure, stable quality, high mechanical efficiency, easy to achieve automation and many other advantages. However, hydraulic technology also has the shortcomings of oil leakage, oil temperature change affecting the control of running speed, noise, expensive cost and high maintenance cost.

    The difference between the plunger stroke adjustable cylinder and the piston stroke adjustable cylinder is that the piston in the stroke adjustable cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type stroke adjustable cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

    The stroke adjustable cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the stroke adjustable cylinder should pay attention to: the operation should be as far away from the stroke adjustable cylinder as possible, to avoid falling objects, knocking, rubbing the stroke adjustable cylinder coating. When cleaning the stroke adjustable cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the stroke adjustable cylinder when the oil temperature exceeds 70 ° C.

    Protection of the stroke adjustable cylinder surface: During the dismantling process, safety protection should be carried out on the stroke adjustable cylinder to prevent objects from falling and welding slag from falling to the surface, causing damage to the stroke adjustable cylinder surface. In the process of propulsion, the damaged pipe segments should be prevented from falling and smashing, and the slurry remaining on the surface of the stroke adjustable cylinder should be cleaned up in time.

    Answers to some questions about stroke adjustable cylinder:

    About the hydraulic cylinder wall thickness problem?
    Hydraulic cylinder wall thickness calculation formula: t=PD/200St= pipe wall thickness (minimum thickness) mmP= maximum pressure kg/cm2? d= inner diameter mm? S=δ/5 safety factor δ= minimum tensile strength This case: set the cylinder material 45#, tensile strength 58kg/cm2t=(640X40)/(200X11.6)t=11mm piston output (i.e. Thrust) calculation formula: F1=PD2X(3.14/4)F1=640X42X0.785=8,038kg Note: Square numbers will not be used, all 2's in the text are square codes.

    What is the pressure provided for a 63-bore cylinder with a pressure of 2 mpa?
    2 mpa pressure is equivalent to 20 kg per square centimeter, 6.3 cm straight longitude, 3.15 cm radius, square, multiplied by, calculated an area of about 31.5 square centimeters, multiplied by 20 kg, the pressure is about 630 kg.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 襄汾县| 赤壁市| 闵行区| 富阳市| 安岳县| 阳原县| 扎兰屯市| 福州市| 旬邑县| 井陉县| 印江| 曲沃县| 曲周县| 石楼县| 嘉鱼县| 安溪县| 当阳市| 清镇市| 金山区| 运城市| 朔州市| 江源县| 深州市| 鄂托克前旗| 商水县| 观塘区| 曲周县| 闽清县| 二连浩特市| 无棣县| 富顺县| 灯塔市| 莱西市| 霸州市| 兴化市| 桐柏县| 三门峡市| 大同县| 山阴县| 安吉县| 陵水|