<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    servo cylinder Sold to Tunisia

    Release time:2023-11-24 08:39:28 Hits: Current position: Home > News

    This article mainly introduces:

    Tunisia hydraulic cylinder,servo cylinder manufacturer,servo cylinder

    Tunisia servo cylinder

    (Tunisia servo cylinder,produced by Hengyu Hydraulic Cylinder Factory)

    servo cylinder are widely used in Tunisia,because of long service life,smooth movement,high work efficiency.So our company has designed servo cylinder for customers from Tunisia.

    Introduction to servo cylinder:

    When the servo cylinder is installed, the piston and the servo cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the servo cylinder head boss is easy to cause scars when it hits the inner surface of the servo cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized servo cylinders, only careful and careful operation can be avoided.

    The assembly work of the servo cylinder has a great impact on the quality of the servo cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

    The piston rod of the servo cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

    1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

    Answers to some questions about servo cylinder:

    Why does the hydraulic cylinder rebound after the rod cavity is extended into place?
    The reason is that after the rod cavity is extended into place, the rod cavity and the rodless cavity are connected, so that the cylinder moves towards the rod cavity. After connecting, it is equivalent to the hydraulic oil directly driving the cylinder with an area equal to the piston rod. After the end of this problem, it is estimated that the seal is not very good, and the two cavities are connected after the pressure is increased to a certain extent; Or there is a problem in the valve, so that the two chambers are connected after reaching a certain pressure. Other phenomena: If the load is increased to a certain extent, no matter which side of the solenoid valve is energized, the cylinder will move to the rod cavity.

    What kind of seal ring we should choose for 120Mpa hydraulic cylinder?
    The sealing rings used in mining machinery are high pressure, which can reach 150MPa. It is generally composed of three parts, the guide ring, the sealing body and the elastomer. It's not a special structure. It's more mature. Usually said mountain circle, bud circle.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 榆中县| 贡山| 湘阴县| 瓮安县| 六安市| 阜康市| 沁水县| 岳阳市| 锡林浩特市| 盐池县| 章丘市| 山东省| 孝昌县| 明溪县| 寿阳县| 洪雅县| 惠东县| 宿迁市| 剑河县| 来凤县| 攀枝花市| 磐安县| 汤原县| 醴陵市| 宁强县| 潞西市| 蓬溪县| 万源市| 绥德县| 英德市| 泸州市| 陆良县| 平果县| 南投市| 鄢陵县| 普兰店市| 丘北县| 银川市| 静宁县| 通道| 铁岭县|