<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    punch machine hydraulic cylinder Sold to Greece

    Release time:2023-11-26 09:50:17 Hits: Current position: Home > News

    This article mainly introduces:

    Greece hydraulic cylinder,punch machine hydraulic cylinder manufacturer,punch machine hydraulic cylinder

    Greece punch machine hydraulic cylinder

    (Greece punch machine hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

    punch machine hydraulic cylinder are widely used in Greece,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed punch machine hydraulic cylinder for customers from Greece.

    Introduction to punch machine hydraulic cylinder:

    When the punch machine hydraulic cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the punch machine hydraulic cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

    Regular maintenance of the punch machine hydraulic cylinder includes: regular tightening, punch machine hydraulic cylinder fastening screws and gland screws, punch machine hydraulic cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the punch machine hydraulic cylinder once a year. Clean regularly, the punch machine hydraulic cylinder is cleaned every other year, and the seals are replaced while cleaning.

    Because of the slightly complex structure of the buffer punch machine hydraulic cylinder, sometimes there will be problems, such as when the punch machine hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

    When the oil pressure of the punch machine hydraulic cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

    Answers to some questions about punch machine hydraulic cylinder:

    Why are the hydraulic cylinders out of sync? The reasons for the unsynchronous operation are as follows: 1, the deviation of the external load of the two cylinders, such as the different resistance and friction of the two cylinders will lead to imbalance. The displacement of the cylinder with low resistance will be larger. 2, the difference in internal friction, such as the difference between the piston and the cylinder of each cylinder, the friction between the piston rod and the seal causes the cylinder to be out of sync. 3. The different resistance of hydraulic oil along the pipeline of the two cylinders causes the cylinder to be out of sync. 4, the deviation of the control original adjustment causes the deviation of the flow to be out of sync, such as the use of an independent throttle valve for each cylinder will appear the difference in the flow of oil in and out of the oil affecting the synchronization of the two cylinders. 5. The cylinder support point of the supported part is initially different.

    Hydraulic cylinder load algorithm?
    If it is thrust, load = working pressure x piston area. If it is pulling force, load = working pressure x(piston area - piston rod area).

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 兴安盟| 馆陶县| 阿尔山市| 云安县| 文水县| 永年县| 辽源市| 高安市| 博野县| 万年县| 沈丘县| 瑞昌市| 潞西市| 团风县| 手游| 瑞金市| 余庆县| 鹿邑县| 上思县| 花莲市| 桂平市| 黑山县| 阳谷县| 高密市| 虹口区| 铜梁县| 葵青区| 凉城县| 民县| 瑞金市| 和静县| 高要市| 玉树县| 丘北县| 普兰县| 石家庄市| 若羌县| 兴宁市| 昔阳县| 高要市| 肇东市|