<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    track steering cylinder Sold to Korea

    Release time:2023-12-01 11:06:39 Hits: Current position: Home > News

    This article mainly introduces:

    Korea hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

    Korea track steering cylinder

    (Korea track steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

    track steering cylinder are widely used in Korea,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed track steering cylinder for customers from Korea.

    Introduction to track steering cylinder:

    When the track steering cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the track steering cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil track steering cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical track steering cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the track steering cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

    If it is found that the track steering cylinder lubrication is poor or the track steering cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the track steering cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the track steering cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the track steering cylinder center line. In this way, when the piston works in the track steering cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the track steering cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

    Disassembly track steering cylinder: When disassembly track steering cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the track steering cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the track steering cylinder.

    When purchasing the track steering cylinder, try to clarify the following parameters of the track steering cylinder: A. track steering cylinder diameter, rod diameter, stroke; B. Working pressure or track steering cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right track steering cylinder type can be found accurately and quickly.

    Answers to some questions about track steering cylinder:

    How to remove the air in hydraulic cylinder?
    Connected the cylinder to the system, and reciprocating move with full stroke several times, then the air can be eliminated . There is also a clunky method as follows: first remove the rod cavity oil pipe, connect the rodless cavity oil circuit to extend all the cylinders, and then remove the rodless cavity oil pipe, connect the rod cavity oil pipe and withdraw all the cylinders, and then connect the rodless cavity oil pipe, so that there is no air in the cylinder.

    Do the collecting cylinder, distributing cylinder and distributing cylinder on the organic heat carrier boiler need to be notified separately as the pressure vessel for construction?
    Do not need to be installed as a separate pressure vessel to inform, according to the organic heat carrier boiler can be informed. Write a "special equipment installation, renovation and maintenance notice" issued on it.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 武乡县| 山丹县| 青田县| 迭部县| 湖州市| 白水县| 南皮县| 德清县| 岑溪市| 黔西县| 舒兰市| 巴彦淖尔市| 六枝特区| 淮南市| 西乡县| 孟州市| 吴忠市| 牡丹江市| 双桥区| 江油市| 当涂县| 阿拉善左旗| 扬州市| 五大连池市| 陇川县| 南陵县| 肇州县| 洞口县| 庐江县| 嘉义市| 剑阁县| 伊宁市| 化州市| 唐海县| 宝坻区| 新余市| 新龙县| 衡南县| 扎鲁特旗| 长治县| 思南县|