trunnion cylinder Sold to Australia

This article mainly introduces:

Australia hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

(Australia trunnion cylinder,produced by Hebei Hengyu company）

trunnion cylinder are widely used in Australia，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed trunnion cylinder for customers from Australia.

Introduction to trunnion cylinder:

trunnion cylinder body inspection: The inner surface of the trunnion cylinder and the piston seal are the main factors causing the leakage in the trunnion cylinder, if the trunnion cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the trunnion cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

trunnion cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

If it is found that the trunnion cylinder lubrication is poor or the trunnion cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the trunnion cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the trunnion cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the trunnion cylinder center line. In this way, when the piston works in the trunnion cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the trunnion cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

When the trunnion cylinder is installed, the piston and the trunnion cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the trunnion cylinder head boss is easy to cause scars when it hits the inner surface of the trunnion cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized trunnion cylinders, only careful and careful operation can be avoided.

Answers to some questions about trunnion cylinder:

Is rubber or polyurethane better for V-ring of hydraulic cylinder?
The hydraulic cylinder V-type seal ring is better with polyurethane, and chlorine rubber is used for various chemicals and high temperatures, especially when there are wear-resistant requirements, polyurethane rubber is needed. But the price of polyurethane rubber is much more expensive than the price of rubber. However, the V-ring material is most commonly used in nitrile and neoprene rubber, and natural rubber is used for sealing water and air. Butyl rubber is used for non-combustible hydraulic fluids and phosphate ester hydraulic fluids. The advantage is that the price is cheaper than the polyurethane material, and the disadvantage is that it is not wear-resistant and the anti-aging property is relatively poor.

How to judge the leakage in the cylinder?
Common judgment method: In the production site, people make full use of watching, listening, smelling, touching and other sensory ways, by observing that the cylinder can not move or delay the action or feel the oil temperature change, vibration and noise, etc., and then judge whether the cylinder has internal leakage according to experience. Another method commonly used in the field is to extend the cylinder in place to ensure that the cylinder does not have any load and will not retract (to prevent the cylinder from internal leakage accidents), turn off the machine, and then remove the tubing with the rod cavity, and then press the switch that pulls out the cylinder (do not press the wrong switch). If the oil nozzle with the rod cavity drains the cylinder internally, If there's no oil coming out, you have to think about something else going wrong.