<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    steering cylinder Sold to Croatia

    Release time:2023-11-09 08:46:39 Hits: Current position: Home > News

    This article mainly introduces:

    Croatia hydraulic cylinder,steering cylinder manufacturer,steering cylinder

    Croatia steering cylinder

    (Croatia steering cylinder,produced by Hengyu Hydraulic Co., Ltd)

    steering cylinder are widely used in Croatia,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed steering cylinder for customers from Croatia.

    Introduction to steering cylinder:

    When the steering cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the steering cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the steering cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

    If air enters the hydraulic system, the steering cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

    steering cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

    When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the steering cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

    Answers to some questions about steering cylinder:

    Does the sealing string of the upper and lower chamber of the hydraulic cylinder fall by itself?
    It is possible, the probability accounts for 85% (depending on the weight), the weight is less than the system resistance, may not fall, the weight is greater than the system resistance, will not necessarily fall, so often check the equipment, safety first, find the problem in time to solve, the cylinder is not very expensive parts, maintenance does not cost much money, However, accidents caused by cylinder failure will lose several times the cost.

    What does cylinder hob125*100 mean?
    HOB is a series of hydraulic cylinder products, the use of pressure 14MPA, tie rod structure. 125 refers to the diameter of the cylinder and 100 refers to the stroke. The unit is millimeters.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 睢宁县| 沧州市| 阿鲁科尔沁旗| 荔浦县| 新化县| 宜春市| 五家渠市| 额敏县| 汶上县| 卢氏县| 安泽县| 定日县| 温泉县| 阳原县| 上林县| 泽普县| 洱源县| 萍乡市| 滕州市| 麟游县| 三门峡市| 崇州市| 宁都县| 汝阳县| 山阴县| 安国市| 偃师市| 永济市| 南川市| 屏南县| 额济纳旗| 广宁县| 岑巩县| 上犹县| 恩平市| 乌兰县| 肥城市| 和顺县| 哈密市| 鲜城| 安乡县|