steering power cylinder Sold to Latvia

This article mainly introduces:

Latvia hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

(Latvia steering power cylinder,produced by Hengyu Hydraulic Co., Ltd）

steering power cylinder are widely used in Latvia，because of clever hydraulic energy conversion，no transmission clearance，powerful torque.So our company has designed steering power cylinder for customers from Latvia.

Introduction to steering power cylinder:

In recent years, the processing process of the steering power cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

In the process of using the steering power cylinder, sometimes such a problem will occur, the steering power cylinder can not act immediately after the instruction of the steering power cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil steering power cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

In order to ensure the service life of the steering power cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

When the initial action of the steering power cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the steering power cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

Answers to some questions about steering power cylinder:

Why the lifting cylinder falling by itself?
May be there is a pressure relief point. Check and repair the following parts: whether there is oil leakage in the transparent pipe at the top of the cylinder: the cylinder oil seal is broken, and the cylinder and oil seal need to be replaced; No: The multiway valve has pressure relief and needs to be repaired. Maintenance in accordance with routine maintenance items can reduce mechanical failures: 1. Check whether the thermostat works normally. 2, check the transmission shift work is normal. 3. Check the tightness of the fan belt. 4, check whether the diesel tank oil inlet filter is blocked or damaged, and clean or replace the filter. 5. Check and adjust the valve clearance.

What are the differences between hydraulic cylinder and pneumatic cylinder, what are their advantages and disadvantages?
Hydraulic Cylinder: small body and large force, constant speed and variable speed (easy to change), the adjustment of output is also convenient, and the degree of freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Pneumatic Cylinder: easy to control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, so it is more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion. Because the pressure used in the pneumatic system is generally in the range of 0.2-1.0Mpa, the cylinder is not suitable for high power component.