<table id="kaokc"><wbr id="kaokc"></wbr></table>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    <rt id="kaokc"></rt>
  • <li id="kaokc"><source id="kaokc"></source></li>
  • <rt id="kaokc"><delect id="kaokc"></delect></rt>
    High quality hydraulic equipment manufacturers!
    TELL:+8613184968882

    pressure retaining cylinder Sold to Croatia

    Release time:2023-12-05 14:27:30 Hits: Current position: Home > News

    This article mainly introduces:

    Croatia hydraulic cylinder,pressure retaining cylinder manufacturer,pressure retaining cylinder

    Croatia pressure retaining cylinder

    (Croatia pressure retaining cylinder,produced by Hebei Hengyu company)

    pressure retaining cylinder are widely used in Croatia,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed pressure retaining cylinder for customers from Croatia.

    Introduction to pressure retaining cylinder:

    When the pressure retaining cylinder is installed, the piston and the pressure retaining cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the pressure retaining cylinder head boss is easy to cause scars when it hits the inner surface of the pressure retaining cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized pressure retaining cylinders, only careful and careful operation can be avoided.

    If air enters the hydraulic system, the pressure retaining cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

    1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

    pressure retaining cylinder body inspection: The inner surface of the pressure retaining cylinder and the piston seal are the main factors causing the leakage in the pressure retaining cylinder, if the pressure retaining cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the pressure retaining cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

    Answers to some questions about pressure retaining cylinder:

    How to disassemble the big nut that excavate the oil cylinder piston of the excavator?
    If you want to be safe, look for a special unloading place for this thing, which is an oil cylinder on top of a turntable with a large nut attached to the center of the turntable. If you're in the field just pin the head of the cylinder to one end, use a big homemade wrench to hold the nut in place, and then get a digging machine and push it down, and it opens.

    What are the standard cylinder models for hydraulic cylinders?
    National standard GB/T2348-1993 specifies the hydraulic cylinder inner diameter series, you can check GB/T2348-1993 relevant regulations.

    Back to list Recommended article

    Leave a message if you have any questions.

    Send
    Email

    Email:hsslrubbertech@gmail.com7x24 hours

    Glad to receive your consultation!:

    Service
    Tel

    +8613184968882
    7x24hours service

    Add
    Wechat

    Add Wechat
    TOP
    主站蜘蛛池模板: 肃宁县| 综艺| 奉节县| 镇坪县| 丰宁| 奇台县| 句容市| 景泰县| 中西区| 云阳县| 镇安县| 司法| 略阳县| 定州市| 九寨沟县| 道真| 北京市| 江油市| 古田县| 衡阳市| 合水县| 无棣县| 屏东市| 霞浦县| 扶沟县| 体育| 肃宁县| 积石山| 得荣县| 汉寿县| 广宗县| 佛冈县| 虹口区| 申扎县| 五指山市| 新安县| 若尔盖县| 金坛市| 漯河市| 溧阳市| 济阳县|